ifudocs

Digital EU declaration of conformity for machinery

From 20 January 2027 a machine builder may replace the paper declaration of conformity with a web address or a QR code printed in the instructions. An amendment known as Omnibus IV, agreed by negotiators in June 2026, would make the digital form the only one. It has not been adopted, so paper stays lawful.

The declaration can be digital in 2027 and would have to be digital later

Two texts matter. One is the Machinery Regulation as adopted. The other is the amendment that Parliament and Council negotiators agreed and that neither institution has voted into law.

TextWhat it says about the declarationStatus on 16 November 2026
Regulation (EU) 2023/1230, Article 10(8)The declaration travels with the machine on paper, or the instructions carry a web address or machine-readable code that leads to it. The builder chooses.Law. Applies from 20 January 2027.
Omnibus IV, agreed text, Article 5The declaration is drawn up in digital format. The machine is accompanied by an address or code through which the declaration can be directly accessed. The paper option is gone.Agreed on 9 June 2026, approved in committee on 14 July 2026. Parliament has not voted. The indicative plenary date is 23 November 2026.
Omnibus IV, agreed text, Articles 8 and 9The machinery changes apply 30 months after the amending regulation enters into force. Machines placed on the market before that date under the existing rules stay lawful.No calendar date exists until the act is published in the Official Journal.

The agreed text has not passed legal-linguistic revision, so single terms may still change. This page is a plain summary and not legal advice.

From 20 January 2027 the declaration may be a link in the instructions

Article 10(8) of Regulation (EU) 2023/1230 gives the builder two routes. The machine is accompanied by the EU declaration of conformity from Annex V, Part A. Or the instructions for use state a web address or a machine-readable code where the declaration can be found.

The second route comes with a duration. A declaration supplied this way stays online for the expected lifetime of the machine, and for at least ten years after the machine is placed on the market or put into service. A machine delivered in March 2027 needs its declaration reachable until March 2037 at the earliest.

The same ten years apply to digital instructions under Article 10(7), which is why we keep the two documents at the same address.

Omnibus IV would remove the paper declaration for machinery

The agreed wording is public as committee document PE790.900. Article 5 of that document holds the amendments to the Machinery Regulation.

Article 10(2) would require the manufacturer to draw up the declaration in digital format. The first subparagraph of Article 10(8) would be replaced, so that the machine is accompanied by a web address or a machine-readable code through which the declaration can be directly accessed. Recital 6 says the declaration should exist in electronic form only.

The rule on instructions is left alone. Article 5 does not amend Article 10(7), so a user who asks for paper instructions at the time of purchase still receives them free of charge within one month.

Industry statements from February 2026 said machinery would get no transition period. They were written before the agreement and do not match Article 9 of the agreed text, which gives 30 months.

Direct access means the declaration opens without a login, a form or an app

The articles of the agreed text use the words "directly accessed" and do not define them. Recital 7 describes what is meant. Intermediate steps such as landing pages are kept to a minimum. Access is free. The user does not log in, does not register, does not hand over personal data and does not install an additional application.

Measured against that description, the common setups look like this. The right-hand column is our reading of a recital in a text that can still change.

What the code on the machine opensAgainst recital 7
The declaration file itselfNo intermediate step. Fits the description.
A page for that machine, with the declaration one tap awayOne intermediate step, no login, no data. Close to the description. Whether one page is "a minimum" is not settled.
A search page where the user types the serial numberAn extra step and an input from the user. The recital points away from it.
A customer portal with a loginDoes not fit. The recital excludes login and registration.
An app from an app storeDoes not fit. The recital excludes additional applications.

An ifudocs machine page is the second row. The scan opens the page for that serial number and the declaration is one tap from there. The declaration also has an address of its own, so a code that opens the file itself can be printed if the final text asks for that.

The agreed text does not say whether the code leads to one machine or one model

Article 10(8) as amended refers to the EU declaration of conformity set out in Annex V, Part A. It does not say whether the address or code must lead to the declaration of the individual machine or of the model. For two other regulations the agreed text contains a rule on one code for a series. For machinery it contains none.

Our view is that a builder does not need to wait for the answer. An address per serial number works under both readings. If the final text is read as the individual machine, the address exists. If a declaration per model is enough, forty addresses lead to the same file.

The opposite choice is harder to undo. One code per model, printed on forty delivered machines, cannot be turned into forty codes afterwards.

The declaration would name a digital contact, and a phone number does not count

The agreed text adds a definition as point 22a of Article 3. A digital contact is an up-to-date, freely accessible online channel, such as an email address, that can be used without registration and without extra software. It would appear in the declaration under Annex V and in the instructions under Annex III.

Recital 9 excludes automated replies, chatbots, fax and telephone. A contact form that answers with an automatic message would not meet it. An email address that a person reads would.

The declaration stays online for at least ten years, and the address written in it has to work for as long. A role address such as documentation@ outlives the employee who set it up.

What a machine builder can settle before the final text

Four decisions hold under the Regulation as adopted and under the agreed text. Neither text requires them in these words. They follow from the two features both texts share, an address that leads to the declaration and ten years of availability.

  • The address sits on a domain the builder owns. A printed code cannot be changed after delivery. An address on your own domain can be pointed at a different server when the hosting changes.
  • Each machine has its own address. It covers both readings of the open question, and it records which declaration went out with which serial number.
  • Nothing stands in front of the declaration. No login, no form, no app. Of the points in recital 7 this is the one stated most plainly.
  • The contact in the declaration is a role mailbox. Someone reads it, and it does not carry a person's name.

The dates to check again are the plenary sitting indicated for 23 November 2026 and the day the act appears in the Official Journal, when the 30 months start to run. We update this page on both.

Common questions about the digital declaration of conformity

Is a digital declaration of conformity mandatory for machinery from January 2027?

No. From 20 January 2027 Article 10(8) of Regulation (EU) 2023/1230 allows a paper declaration with the machine or a link in the instructions. The builder chooses.

When would the digital declaration become mandatory?

If Omnibus IV is adopted as agreed, 30 months after the amending regulation enters into force. The act has not been published, so the date cannot be calculated. On 16 November 2026 Parliament had not voted.

Can a QR code on the machine lead to the declaration of conformity?

Yes. The Regulation speaks of an internet address or a machine-readable code, and a QR code is a machine-readable code. Under the adopted text the address or code is stated in the instructions. Under the agreed text it accompanies the machine.

Can the declaration and the manual share one QR code?

Neither text we read asks for separate codes. One page for the machine can hold both documents, as long as the declaration opens from it without a login or a form. If the final text requires the code to open the declaration file itself, the declaration needs a code of its own.

How long does a digital declaration of conformity stay online?

For the expected lifetime of the machine and at least ten years after it is placed on the market or put into service. The agreed text leaves that rule in place.

Does the declaration have to be per machine or per model?

The agreed text does not say. An address per serial number works either way.

Does Omnibus IV change paper instructions on request?

Not for machinery. The agreed text does not amend Article 10(7), so paper instructions are still supplied free of charge within one month if the user asks at the time of purchase.

How ifudocs handles the declaration

The declaration is one of the documents on the machine page, next to the manual, on your own subdomain. The page is tied to the serial number and opens without a login. On the demo machine page it is listed under the other documents for that machine, with the date it was signed.

We host the declaration. We do not draw it up and we do not assess conformity. That stays with the manufacturer under Article 10.

See how it works and the prices.

ales@ifudocs.com

Sources and changes to this page